Backflow welding guarantee and welding skills for 华体会体育·（中国）股份有限公司官网A chip processing

Reflow soldering is an indispensable manufacturing stage in SMT chip processing, and it will continue to endanger the welding quality of SMT chip processing. At present, most SMT production, processing and welding in the factory are all reflow processing processes. So what exactly is reflow soldering? The following technICal professional 华体会体育·（中国）股份有限公司官网A chip processor Fanyi Circuit gives you a SIMple introduction.

In simple terms, reflow soldering actually means that there is a heating power circuit in the welding furnace, which heats the gas or N2 to a sufficiently high temperature and blows it to the 华体会体育·（中国）股份有限公司官网 circuit board with components already attached, so that the solders on both sides of the components are melted and bonded to the computer motherboard. This kind of production and processing method can accelerate the whole process of SMT welding to a level that can not be reached by manual production and welding, and can easily complete mass production, and the cost of 华体会体育·（中国）股份有限公司官网A production and processing can be reasonably controlLED.

华体会体育·（中国）股份有限公司官网A processing

In reflow welding, the welding layer of 华体会体育·（中国）股份有限公司官网A based steel plate is first covered by solder paste, which is generally the compound of solder, SMAll ball and bead of soldering fluid.

The solder paste is automatically packaged and printed according to the position of the screen plate, so that the solder paste can only be left in the area where the terminal blocks of components must be welded.

After SMT components and parts are mounted on the 华体会体育·（中国）股份有限公司官网A base steel plate, the quality inspection outside the furnace is carried out. It is determined that the quality clearance board will be put on the chain rail and transferred to the reflow soldering furnace, and the temperature will rise above the solder melting point in the reflow soldering mechanical equipment. Then the solder flows back to the terminal block of the device, and then the circuit board

Precautionary Techniques for Welding Porosity in 华体会体育·（中国）股份有限公司官网A processing

Porosity caused by 华体会体育·（中国）股份有限公司官网A plate welding, also known as bubble, is generally caused by flow back welding and wave soldering during 华体会体育·（中国）股份有限公司官网A processing. So how to prevent porosity caused by 华体会体育·（中国）股份有限公司官网A production, processing and welding?

1. Baked

华体会体育·（中国）股份有限公司官网 and Electronic devices exposed to air for a long time shall be baked to avoid moisture.

2. Solder paste supervision

Solder paste with moisture is also very easy to cause pores and solder beads. Solder pastes with high cost performance ratio shall be used first. The temperature rise and mixing of solder pastes shall be strictly observed according to the actual operation. The time for the solder pastes to be exposed to the air shall be as short as possible. After the packaging and printing of solder pastes, the solder pastes must be immediately returned for welding.

3. Workshop environment humidity supervision

The environmental humidity of the monitoring workshop with the scheme is controlled between 40-60%.

华体会体育·（中国）股份有限公司官网A welding

4. Set effective furnace temperature curve

Carry out temperature control detection twice a day to improve the furnace temperature curve, and the temperature rise speed cannot be too fast.

5. Flux painting

When passing the wave crest welding machine, the amount of spray paint of the flux shall not be too much, and the spray paint is effective.

6. Raise furnace temperature curve

The temperature of the heating zone shall be specified, and shall not be too low, so that the flux can be fully evaporated, and the speed of passing through the furnace shall not be too fast.

There will be many elements harmful to bubbles, which can be analyzed from the aspects of 华体会体育·（中国）股份有限公司官网 design, 华体会体育·（中国）股份有限公司官网 environmental humidity, temperature control, flux (spray size), chain speed, tin wave height width ratio, solder wire composition and so on. It is possible to get a good manufacturing after several adjustments.