Stacking Design Method of Balanced 华体会体育·（中国）股份有限公司官网 Boards

Stacking design Method of Balanced 华体会体育·（中国）股份有限公司官网 boards
Designers can design an odd 华体会体育·（中国）股份有限公司官网 If routing does not require additional layers, why use it? Won't reducing the number of layers make the board thinner? If there is one less circuit board, wouldn't the cost be lower? However, in some cases, adding a layer can actually reduce costs The circuit board has two different structures: core structure and foil structure In the core structure, all conductive layers in the circuit board are coated on the core material; In the foil structure, only the internal conductive layer of the circuit board is coated on the core material, and the external conductive layer is coated with the foil coated dielectrIC plate All conductive layers are bonded together by a multilayer lamination process using dielectrics The nuclear material is the factory's double-sided foil Because each core has two sides, when fully utilized, the number of conductive layers on the 华体会体育·（中国）股份有限公司官网 is uniform Why not use the foil on one side and use the core structure for the rest? The main reason is 华体会体育·（中国）股份有限公司官网 board and 华体会体育·（中国）股份有限公司官网 board
华体会体育·（中国）股份有限公司官网 board

Cost advantages of even laminates
Since there are fewer dielectric and foil layers, the raw material cost of odd 华体会体育·（中国）股份有限公司官网 is slightly lower than that of even 华体会体育·（中国）股份有限公司官网. However, the processing cost of odd 华体会体育·（中国）股份有限公司官网 is significantly higher than that of even 华体会体育·（中国）股份有限公司官网. The processing cost of the inner layer is the same; However, the foil/core structure significantly increases the processing cost of the outer layer. Singular layer 华体会体育·（中国）股份有限公司官网 needs to add non-standard laminated core layer welding process on the basis of core structure process. Compared with the core structure, the factory adding foil outside the core structure will lose productivity. Before laminated bonding, the outer core needs additional treatment, which increases the risk of scratches and etching errors in the outer layer.
Balanced structure to avoid bending
The reason why 华体会体育·（中国）股份有限公司官网 with odd layers is not designed is that odd layers are easy to bend. When the 华体会体育·（中国）股份有限公司官网 is cooLED after the multi-layer circuit bonding process, the different laminating tensions of the core structure and the foil covering structure will cause the 华体会体育·（中国）股份有限公司官网 to bend. As the thickness of the board increases, the risk of bending composite 华体会体育·（中国）股份有限公司官网 boards with two different structures increases. The key to eliminating board flex is balanced stacking. Although 华体会体育·（中国）股份有限公司官网 boards with a certain curvature meet the requirements of the specification, the subsequent processing efficiency will be reduced, resulting in additional costs. Due to the special equipment and process required for assembly, the accuracy of placement of this part will be reduced, thus affecting the quality.
Use evenly layered 华体会体育·（中国）股份有限公司官网s
When odd 华体会体育·（中国）股份有限公司官网 boards appear in the design, the following methods can be used to achieve balanced stacking, reduce 华体会体育·（中国）股份有限公司官网 manufacturing costs, and avoid 华体会体育·（中国）股份有限公司官网 bending. The following methods are listed in order of priority.
1) A signal layer and use. This method can be used if the power supply layer of the 华体会体育·（中国）股份有限公司官网 board is even and the signal layer is odd. The added layers will not increase the cost, but can shorten the lead time and improve the quality of 华体会体育·（中国）股份有限公司官网.
2) Add additional power layers. This method can be used if the power plane of the design 华体会体育·（中国）股份有限公司官网 is odd and the signal plane is even. A SIMple way is to add a formation in the middle of the stack without changing other settings. First, route the 华体会体育·（中国）股份有限公司官网 according to the odd number of layers, then copy the middle ground plane and MARK the remaining layers. This is the same as the electrical characteristics of the thickened foil.
3) Add a blank signal layer near the center of the 华体会体育·（中国）股份有限公司官网 stack. The method eliminates the stacking imbalance and improves the quality of 华体会体育·（中国）股份有限公司官网. First route the odd numbered layers, then add a blank signal layer and mark the remaining layers. It is used in microwave circuit and mixed medium (medium with different dielectric constant) circuit.
Advantages of balanced lamination 华体会体育·（中国）股份有限公司官网 board: low cost, not easy to bend, short delivery time, and guaranteed quality
The above is the explanation given by the editor of 华体会体育·（中国）股份有限公司官网 circuit board company. If you want to know more about 华体会体育·（中国）股份有限公司官网A, you can go to our company's home page to learn about it. In addition, our company also sells various circuit boards,
High Frequency Circuit Board and SMT chip are waiting for your presence again.